Asus Monitor Need to Use Vga Again After Hdmi

Blog

what to do if your monitor is blackness and says vga no bespeak asus

• Thread starter Ruta Kruze
• Start engagement Aug 18, 2014

Status

Not open for farther replies.

• #ane

when I trun my computer on my monitor says asus and then vga no signal and so it goes black and there is an orangish light. please assist me.

Jan v, 2014

2,861

3

xiv,960

710

• #two

We need a lot more details to give you a adept reply. What are the details of your build - motherboard, CPU, RAM, PSU, monitor, GPU? Is it a laptop or desktop? How onetime is the build? Did you build it yourself or is it store-bought? Is this a new development on a previously working build, or is this the first fourth dimension you lot've fired the arrangement upward? Any details surrounding the problem will assistance a lot when nosotros effort to practice remote diagnostics at 2d-paw.

Jun 10, 2014

515

0

5,160

69

• #3

check cables..brand sure their both fully in and locked. Check the source..have you used vga, dvi, or hdmi? You lot might need to alter the source on your monitor depending upon what setup you're actually using.

employ deductive reasoning..go down the line to narrow down where the issue is.

• #4

The monitor does non automatically select the input source. You must apply the select input button just to the left of the power button. Repeatedly button the button until the correct input source is selected. Unfortunately when the monitor does non detect the selected input it powers downwards and the select input button may not work correctly. A fashion effectually this is to connect the monitor to a VGA input since that information technology what information technology is apparently looking for. Power upwardly the monitor and the input source. Then you tin can use the select input button to change the selection to the appropriate source, HDMI, DVI, etc. Reconnect the monitor to the new input source.

• #v

The monitor does non automatically select the input source. Yous must use the select input button but to the left of the power push button. Repeatedly push the button until the correct input source is selected. Unfortunately when the monitor does not find the selected input it powers downwards and the select input push may not work correctly. A manner around this is to connect the monitor to a VGA input since that information technology what it is apparently looking for. Power upwardly the monitor and the input source. Then you can use the select input button to alter the selection to the appropriate source, HDMI, DVI, etc. Reconnect the monitor to the new input source.

Yous are a life-saver. Your respond helped me solve the monitor problem in a few seconds. My husband is back on the computer listening to his songs. He was a reckoner expert until he developed Parkinson's. I am calculator illiterate and got lucky to observe your caption in a higher place. Muchas Gracias.

• #six

ur pc

hey !!! sushant here !! meet ..i take the same problems and i was suffering it for last 7 days.. it really upsets.. I tried whole goggle for solving this.no solution for this.
but one day It become solved automatically!!! u know how??
1) start your pc .await for screen to display VGA no signal , HDMI -no signal.ur brandish going off.
two) now go depressed. wait two more mins ..and screen comes alive again and ur display is back attempt this.

• #vii

gdretired. yous stone. y'all merely saved me a lot of time! When I turned off the power last dark I must accept inverse the input source.

• #8

one. Press the Ability Button.
2. Y'all will see the ASUS logo for about 5 seconds.
3. The "VGA no signal" message appears.
4. Depending what ASUS monitor model you accept, there should exist a button on the lesser of your monitor that looks similar a rectangle (representing the monitor) with an horizontal line from left to center. Press it as soon every bit y'all see the "VGA No point" message. The push icon might look like this:

5. Doing then volition at present switch to "No DVI SIGNAL" message. If you are using a DVI cord, after a few seconds the Desktop volition pop onscreen. If you are using a HDMI cablevision, however, yous must press the Mode button (#4 above) again until information technology says "HDMI" onscreen. Subsequently a few seconds, the Desktop will pop onscreen.

Notation: Clicking that button many times in a row will not do much. You need to physically see onscreen when it switches from NO VGA Point --> to NO DVI SIGNAL --> to HDMI. Wait a few seconds betwixt pushing that button until yous can read onscreen the messages. Once it sits on HDMI, wait a few seconds until the Desktop shows upward onscreen. Same if you lot are using a DVI cord.

I had this aforementioned problem just now. I loaded this page to discover a solution. I couldn't notice i, and then I troubleshooted on my ain and this is what fabricated information technology piece of work. My model is ASUS VG278HV (27").

• #nine

Omg! I've read and so many of these and unfortunately I had to figure it out myself. None of the solutions helped me. I had my laptop (cleaved screen) set upwards perfectly with my Acer monitor at home. Now I'm on a business trip and it hasn't been connecting saying "no signal". I tried everything, making sure the VGA cord was plugged in and so turning everything on, unplugging everything and turning on and so plugging everything in. Closing the laptop screen while plugged into monitor after powering on... apathetic blah apathetic. After literally trying every possible way and trying all the pointers here, I thought, hmm I haven't tried switching the VGA cord effectually... I doubted that would work but I had no other pick left. And then I unplugged the VGA from the laptop and used that end for the monitor and used the side that was in the monitor and used it in the laptop..... wtf?! Voila! It worked! Hahahah wth?! It was literally that uncomplicated and still makes no sense to me, just I decided to post it here in case information technology helps someone

Condition

Not open up for farther replies.

Thread starter	Similar threads	Forum	Replies	Appointment
J	Question Flickering (blackness) issue with new MSI Optix display	Displays	1	Mar 24, 2022
A	Question Monitor temporarily going black when new programme starts ?	Displays	0	Mar xviii, 2022
D	Question Black horizontal line across screen on Dell monitor ?	Displays	0	Mar 12, 2022
W	[SOLVED] Desk Fan and Monitor Blackness Screen	Displays	9	Mar eight, 2022
	[SOLVED] Monitors not working after plugging in ethernet cable	Displays	3	Mar 5, 2022
T	Question Monitor to laptop, screen goes black to normal repeatedly.	Displays	3	Mar iii, 2022
	Question Monitor goes black and shuts off when gaming ?	Displays	4	Feb 24, 2022
	Question Could a bad SSD crusade the monitors to randomly disconnect ?	Displays	0	February 13, 2022
B	Question Monitors go black when alt tabbing	Displays	ane	Feb seven, 2022
R	Question Monitor has signal, merely a black screen	Displays	0	Sep 22, 2021

• Advert
• Cookies Policies
• Privacy
• Term & Weather
• Topics

freemanmajoysid.blogspot.com

Source: https://forums.tomshardware.com/threads/what-to-do-if-your-monitor-is-black-and-says-vga-no-signal-asus.1934462/

Share this post